Comparative Evaluation of the Clinical Outcome of Direct Pulp Capping Treatment in Permanent Molars

A total of 120 posterior teeth from 60 patients are randomly divided into 4 groups according to the type of treatment; RetroMTA Conventional group, TheraCal Conventional group, RetroMTA laser group, and TheraCal laser group (n = 30).

A checklist is created for each patient following their selection and completion of the consent form. periapical radiography is carried out and cold/heat tests, to confirm the vitality of the teeth. Mouth rinsing is done with 0.2% chlorhexidine oral rinse for 1 minute. All of the patients' teeth are treated by the same dentist. In all groups, if the bleeding persisted for longer than three minutes following pulp exposure would be eliminated from the research.

Clinical procedures Following local anesthetic, the teeth are suitably isolated under a rubber dam and the caries is removed using the appropriate hand and rotating equipment. There will have been tooth cleaning and bleeding control using cotton pellets lightly moistened with sterile saline applied to the exposed site. Patients are randomly divided into two techniques; a conventional technique that acts as a control group in which laser is not used, and a laser-assisted technique in which Diode laser is applied before application of pulp capping materials. The patients are allocated into one of the following groups; RetroMTA Conventional group, TheraCal Conventional group, RetroMTA laser group, and TheraCal laser group.

Conventional Technique (control group) RetroMTA Conventional group (n = 30). After controlling the bleeding, RetroMTA is mixed with the supplied liquid at a W/P ratio of 3 drops per 0.3 g. After 150 seconds, selective etching, application of adhesive material and application of resin composite restorations will occur according to the manufacturer's instructions.

TheraCal Conventional group (n = 30). Subsequent to controlling the bleeding, using a needle-tip syringe, gently apply TheraCal LC resin-modified calcium silicate (Bisco Inc., Schamburg, IL, USA) light-hardening paste to the exposed portion of the pulp in accordance with the manufacturer's recommendations for thickness (1 mm) and curing time (20 Seconds).

Laser-assisted technique Consequent to controlling the bleeding, Diode laser is focused to the exposure sites before the placement of pulp capping materials. The protective goggles for the patient, operator, and assistant are checked. The hemostasis is obtained by the diode 808-nm, laser-assisted procedure (Picasso-AMD, USA) using 1.5 W, continuous wave, fiber diameter of 400 μm, non-initiated and in contact mode, tip angle set at 90°, beam divergence 16°, 2 s per an area with 1-mm diameter, power density 190.98 W/cm2, energy density 381.97 J/cm2, and vertical and horizontal scanning movement on the exposure site. Decontamination of the cavity is performed by 1 W, continuous wave, fiber diameter of 400 μm, non-initiated and in contact mode, tip angle set at 90°, an area with 2-mm diameter per second, power density 31.83 W/cm2, energy density 31.83 J/cm2 per second, and circular movement. The use of diode laser will be used for 1 to 3 seconds. Following to laser application, the pulp capping materials either RetroMTA or TheraCal are placed over the exposure site according to the randomization protocol.

TheraCal laser group (n = 30). Application of TheraCal are occurred as TheraCal Conventional group. RetroMTA laser group (n = 30). Application of RetroMTA are occurred as RetroMTA Conventional group. Restorative procedures The cavities are permanently restored at the same session using universal Adhesive in selective etch technique for enamel margins and self-etch for cavities dentine following a layer of flowable and then nanohybrid composite.

Follow-Up and Evaluation of the Success At each recall examination (1, 3, and 6 months), the information obtained from clinical and radiographic examinations is recorded in a special form. Clinical assessments are performed by applying ice on the buccal side, percussion test to forecast the periradicular involvement of the tooth, and palpation test to forecast the extent of periradicular bone involvement. In addition, follow up of the postoperative pain will be occurred. The clinical failure criteria included the loss of vitality, spontaneous pain, prolonged reactions to thermal stimuli, and tenderness to percussion.

Radiographic assessments are performed by a calibrated endodontist who is also blind to the type of treatment groups. Every digital radiograph is examined for dentin formation, periapical and furcal radiolucency, expansion of the periodontal ligament space, and any pulpal calcifications. After that, every radiograph is scanned and uploaded to the computer for digital analysis. Measurements on the digitized radiographs are performed in the first, third, and sixth months. The increase in dentin thickness is thus measured using Image J program (Microsoft Corp®, Washington, Redmond, USA). The statistical analyses based on the repeated measurements ANOVA are conducted for selected data sets.