Clinical trials: Edentulous Maxilla
Edentulous Alveolar Ridge
Effectiveness of Removable Prosthesis Retained by 4 Implant-supported Locator-Attachments
1. Hypothesis/Specific aims The aim of the present study proposal is to validate an implant treatment concept in the edentulous upper maxilla using four implants-supported locators abutments to retain removable prosthesis.
- Trial name
- LOC (NCT02380404)
- Testing
- Implants-supported locators placement
- Where
- 2 sites in Belgium
- Volunteers
- 30 people, healthy volunteers welcome
- Sponsor
- University of Liege
Completely Edentulous, Implant Assesment
Fully Versus Partially Guided Implants Placement: Measurement of Accuracy of Implant Position and Passivity of Superstructures.
compare fully versus partially guided all on four implants placement immediately loaded by maxillary and mandibular screw retained overdentures: A radiographic and photogrammetric measurement of accuracy of implant position and…
- Trial name
- NCT07174791
- Testing
- cone beam computed tomography, photogrammetric scan using elite scanner (shining 3d)
- Where
- Egypt
- Volunteers
- 16 people, healthy volunteers welcome
- Sponsor
- Mansoura University
Edentulous Alveolar Ridge in the Aesthetic Zone
Aesthetic Outcomes of Single Tooth Implant-supported Restorations in the Anterior Maxilla With Either White Zirconia or Fluorescent White Zirconia Abutments
This study aims to answer the question whether the use of a fluorescent layer over white zirconia abutments will improve the aesthetic outcomes of implant borne single-tooth restorations when compared to the use of non-layered…
- Trial name
- NCT05475249
- Testing
- Implant placement and prothesis made with different types of abutment
- Where
- Spain
- Volunteers
- 40 people, healthy volunteers welcome
- Sponsor
- Universidad Complutense de Madrid
Edentulous Maxilla
Comparing Scanning Accuracy of Full-Arch Maxillary Implants: Extraoral vs. Intraoral Techniques
Data acquisition from the patients: After 4 months of implant placement, three impressions/scans will be made for each patient as follows: Data 1: conventional impression using open tray transfer copings and silicon impression…
- Trial name
- NCT06669065
- Testing
- extraoral versus intraoral scanning techniques
- Where
- Egypt
- Volunteers
- 10 people, healthy volunteers welcome
- Sponsor
- Misr University for Science and Technology
Edentulous Jaw
Intraoral Scanning v.s Desktop Scanning
The aim of this study was to evaluate the effect of intraoral scanning versus desktop scanning on the retention and adaptation of maxillary denture bases in completely edentulous patients.
- Trial name
- NCT06509269
- Testing
- intraoral scanning, Desktop scanning
- Where
- Egypt
- Volunteers
- 20 people, healthy volunteers welcome
- Sponsor
- British University In Egypt
Atrophy of Edentulous Maxillary Alveolar Ridge
Ascending Ramus Versus Chin Cortical Plates for Reconstruction of Atrophic Maxilla
Assessment of ascending ramus cortical plate for reconstruction of atrophic maxillary ridges versus chin cortical plates (Randomized clinical trial)
- Trial name
- NCT03629860
- Testing
- Atrophic maxillary alveolar ridge augmentation
- Where
- Egypt
- Volunteers
- 12 people, healthy volunteers welcome
- Sponsor
- Cairo University
Edentulism Complete
3D Metrology-Based Comparison of Functional Casts Made With Conventional and 3D-Printed Custom Trays
This study will compare the dimensional discrepancies of functional casts obtained using conventional custom trays and 3D-printed custom trays made from PET-G (Polyethylene Terephthalate Glycol) filament.
- Trial name
- NCT07787715
- Testing
- Conventional PMMA Custom Tray, 3D-Printed Custom Tray
- Volunteers
- 30 people, healthy volunteers welcome
- Sponsor
- University of Sao Paulo
Implant Stability
Comparison of Intrasinus and Extrasinus Approach for the Placement of Zygomatic Implants in Severely Resorbed Edentulous Maxillary Arch Using Zygomatic Success Code - An In-Vivo Study
Various approach has outlined in the literature but no clinical studies that have compared the intrasinus and extrasinus approach for the placement of zygomatic implants using zygomatic success code.
- Trial name
- NCT07452068
- Testing
- ZYGOMATIC IMPLANT KIT
- Where
- India
- Volunteers
- 36 people, healthy volunteers welcome
- Sponsor
- Postgraduate Institute of Dental Sciences Rohtak
Complete Edentulism
Denture Retention of Intra-orally Scanned Versus Extra-orally Scanned Digitally Printed Maxillary Denture in Completely Edentulous Patients
The goal of this clinical trial is to evaluate denture retention in intra-orally scanned versus extra-orally scanned digitally printed maxillary dentures in completely edentulous patients. The main question is : 1.
- Trial name
- NCT07290322
- Testing
- Intaorally scanned methods, extraorally scanned methods
- Where
- Egypt
- Volunteers
- 8 people, healthy volunteers welcome
- Sponsor
- Cairo University
Printed Dentures
Effect of Printing Layer Thickness on Growth of Candida Albicans in Completely Edentulous Patients Rehabilitated With 3D-Printed Maxillary Complete Denture Bases.
In completely edentulous patients rehabilitated with 3D-printed maxillary dentures bases, does the printing layer thickness affect candidal adherence and growth on the fitting surface of dentures.
- Trial name
- NCT07303530
- Testing
- printing layer thickness of denture
- Where
- 2 sites in Egypt
- Volunteers
- 10 people, healthy volunteers welcome
- Sponsor
- Cairo University
Edentulous Jaw
In-Vivo Comparison of Different Impression Methods in Complete Edentulous Upper Jaw
In this study, it was aimed to compare the impressions taken with different impression techniques for the production of tissue-supported complete dentures from individuals with complete edentulous upper jaws.
- Trial name
- NCT06400277
- Testing
- Edentulous maxilla final impression for complete denture
- Where
- Turkey (Türkiye)
- Volunteers
- 15 people, healthy volunteers welcome
- Sponsor
- Hacettepe University